At this time, the radio mast icon “ ” will flash (the icon is next to the digital display of time) and the screen will turn dark, this process takes about 7 minutes. The default time zone is Pacific Time -8, if you need to select the time zone that matches your location, press “ ” button to exit from WWVB signal search mode, then refer to page 8 to set the time zone and time). Once the weather station has established a connection to the remote sensor, it will automatically begin to search for WWVB signals to set the time and date (at this time, to prevent the radio clock signal from being interfered with, the backlight will turn dark.

At this time, the RF icon “ ” will appear and flash in the “REMOTE SENSOR” display area of the main unit. After the indoor temperature and humidity detection is completed, the main unit will begin to establish a connection with the remote sensor (note: please keep the channel of the main unit and remote sensor consistent).The LED light flashes once indicating that the remote sensor sends a wireless signal once. Open the cover of remote sensor, choose a channel for remote sensor(1, 2 or 3, and press “ ” button to set the channel of the main unit match to the remote sensor’s), insert 2 x AA batteries observing polarity, then the remote sensor will begin to detect the temperature and humidity.All icons on the screen of main unit will light up for 3 seconds, you will hear a beep, and the main unit will begin to detect the indoor temperature and humidity. Plug in the original power cord or insert 2 x AA batteries observing polarity.Slide up to switch On alarm, slide down to switch Off alarm. Normal Mode Time Setting Alarm Setting Outdoor Temperature Alert Setting Weather Forecast Setting Press Hold Press Hold Press Hold Press Hold Pressī1 Backlight On for 15 Seconds Backlight On for 15 Seconds Backlight On for 15 Seconds Backlight On for 15 Seconds Backlight On for 15 Seconds Backlight On for 15 Seconds Backlight On for 15 Seconds Backlight On for 15 Seconds / /ī2 Switch Display of Calendar or Second Time Setting Confirm and Go to the Next Step / / / / / /ī3 Switch Display of Calendar or Alarm Alarm Setting / / Confirm and Go to the Next Step / / / / /ī4 ☌/☏ Switch Automatic Time Setting Increase Increase Continually Increase Increase Continually Increase Increase Continually Go to the Next Stepī5 3 Channel Switch Channel Searching Decrease Decrease Continually Decrease Decrease Continually Decrease Decrease Continually Back to the Last Step /ī6 Turn On/Off Temperature Alert Outdoor Temperature Alert Setting / / / / / / /ī7 Adjust Brightness of the Backlight in DC Mode Weather Forecast Setting / / / / / / Confirm Setting / MEMī8 View indoor/ outdoor Max/Min Data Clear Max/Min Data / / / / / / / To get accurate readings, please keep the main unit clear of any unusual source of heat or cold (such as lamps, heaters and others) and that the sensor is also protected from direct sunlight, rain, or the heat it may experience from being mounted on a warm wall, or from heat rising from a surface below it. Press “ ” button to exit from the WWVB signal search mode. The backlight is only on for 15 seconds by pressing “ ” button, this process lasts about 7 minutes and the backlight will light up again after synchronization. When the clock is synchronizing the WWVB signal, only “ ” and “ ” buttons work. When plugged in, press “ ” button to keep the backlight always on or adjust brightness. There may be ±5% deviation when humidity is 40%~80%, while ☘% deviation in other ranges.ī9: Alarm On/Off Shift Switch ( 9th page )ī10: USB Charger Output Socket ( 14th page )

There may be ☑☌/1.8☏ deviation when temperature is 0☌~40☌/32☏~104☏, while ☒☌/3.6☏ deviation in other ranges. A4: Remote Temperature Alert ( 12th page)Ī5: Radio Mast Icon, DST, Time/Calendar or Alarm Time( 7-9th page)Ī14: Histogram Shows the Atmospheric Pressure ( 11th page)

My weather indicator not working